Wednesday, July 31, 2019

SB-200 input impedance correction on 10 and 15 meters

I had known that both the 10 and 15 meter band input circuits on my old Heathkit SB-200 linear amplifier were not well matched to my transceiver.  Using this amplifier with a newer radio, would cause the transceiver to fold back on these bands with high SWR.  Referring to the schematic we see that these employ an L-network to attempt to match the input impedance to standard 50 ohm load.

Going through the mathematical exercise for a PI network, which I won't trouble you with here, it stands to reason this would probably work better just like it does on the lower bands.  This more sophisticated matching network filter can have more loss, but that's not something I was worried about.  The limited number of turns on the 10 and 15 meter coil meant that they required some fairly small capacitors to attempt to make the matching come out correctly.  The problem is that those size capacitors are about the same value of some of the stray capacitance I believed to be in and around the wiring.

The plan was to double the number of turns and increase the capacitance required on the Input side of the network.  I then stumbled on this article by PA0FRI who came to the same conclusion.

I stripped the 10 and 15 meter coils from their windings and re-wound with 1mm diameter magnet wire.  Scrounging through the junk box yielded the capacitors that I calculated and were confirmed by PA0FRI.  I didn't have any tuning caps available, so trial and error yielded appropriate values for the output capacitors which had to factor out the stray capacitance in the wiring.

The trick was how to validate and tune the slugs in the inductors.  I've lost the source from a forum post on eHam, but the procedure is to simulate the resistance of the tubes per their data sheet.  So we temporarily place a 220 ohm resistor between the filament lead and then to ground on the chassis.  While manually pressing in the transmit / receive relay an antenna analyzer is used to measure the impedance at the input connector.  After few tweaks of the slugs both bands yielded acceptable impedance at less than 1.5:1 SWR reading.

The final results are below:


Monday, June 24, 2019

Proficiency in "Radio Sport" helps me at work


For those not familiar with the term “Radio Sport”, it is the Amateur Radio activity of contacting as many other stations as possible in a set period of time.  This contest activity involves being able to hear distant stations through noise and interference, as well as exchanging a precise set of information with the other station.  The exchange of information must be exact with no mistakes and no misunderstandings.  The information is logged for future reference to be submitted to the sponsoring organization for points.  Points are for bragging rights, and the sense of accomplishment for success.  The proficiency is good practice in the event of supporting communications during an actual emergency.

In the field of Technical Support, it is important to be brief, but friendly, and always precise.  In the heat of the moment flowery language is not appropriate, sticking to the subject with a balance of courtesy is essential.  The skills I learned in Radio Contesting apply well to situations where asking the right questions without being misunderstood is of primary importance.  The client requesting assistance is sometimes flustered or panicked.  Letting them know you are listening to their problems and calmly providing answers puts the client’s mind at ease.

Speaking on the telephone with a client while they are in a noisy equipment room, is not significantly difficult in comparison to a radio conversation on single sideband with other conversations a few kilohertz up or down the band bleeding into your own conversation.  It does require a good ear for a person’s voice.  Sometimes during a tech support phone call, the person on the other end of the conversation may have an accent.  This is commonplace in radio when speaking with radio operators from around the world.  Getting the questions and answers accurately exchanged when trying to repair equipment using technical terms can be a challenge.  This is where using the International Phonetic Alphabet to spell things out becomes a great tool to ensure accuracy.  If a part or model number is confused it could mean sending the wrong replacement to the client.  Misinterpretations resulting in confusion and delay are not acceptable when a client’s investment is in question.  One should not be afraid to ask the person to repeat themselves or ask them to explain something using different words.  Repeating what you have heard is also a good tool to confirm that the message is received without error or misunderstanding.  This practice is commonplace in radio conversations where noise and interference can often lead to misunderstandings.  Being a parrot provides this crosscheck of accurate information.

In radio conversations the conditions of the band are usually called to blame for any misunderstandings that may arise, whether that is the actual cause or not.  The person’s equipment on the other side of the conversation is not called into question, because that would be confrontational.  The same goes for Technical Support, in that blame is not placed.  Avoiding overuse of the word “YOU” keeps the situation from becoming personal.  Always refer to the problem as a technical task to be overcome, and never succumb to emotional responses when conversations turn away from objective conversation.  My mentor would always say, “They can’t argue with the science.”  If the support engineer remains objective with an attitude of solving the problem logically, the person requesting help usually responses with an attitude of gratitude. 

When time allows establish a good rapport with the person at the other end of the conversation.  Letting them know something about you, or listening to something about them, goes a long way to keeping the conversation friendly.  Listening before speaking goes a long way to let them know they have your attention and best interests in mind.

As it is done in radio the conversation is ended with a word of thanks and good wishes.  Express your gratitude for their patience while working through the problem.  Apologize when required and stick to the science.

This is Eric N3FIX.
73


Tuesday, May 28, 2019

Grid Dip Meter

The grid dip meter (or grid dip oscillator) is a useful tool that deserves some interest today.  They are often found without their coil sets at hamfests.  The grid dip oscillator is instrumented with a current meter on the vacuum tube grid.  This indication in the drop in grid current indicates resonance with a nearby tuned circuit.  When the resonance of the grid dip oscillator matches with a nearby device the oscillator is loaded as the energy transfers out from the circulating current of the LC tank, and is absorbed by the nearby circuit.  The oscillator may be coupled inductively to the coil under test, or capacitively to a coaxial cable.  The grid dip meter can also function to find the resonance of an antenna this way.

A secondary function of this particular Heathkit GD-1B grid dip meter is the DIODE mode.  This allows a pair of headphones to be inserted into the jack.  Tuning the grid dip meter to the resonant frequency of a nearby oscillator will produce a beat tone in the headphones.  This can be useful when neutralizing a transmitter.

Other functions naturally include finding the value of unknown inductor or capacitor components against a known capacitor or inductor.  Determining the selectivity or "Q" of a circuit is also possible, by observing the sharpness of the grid dip.  This function requires the aid of a high impedance volt meter.

Here's the schematic.  It draws current from the mains, and has a set of coils.  At a swap meet, I was able to obtain a FULL set of coils including the low frequency coils.  I knew what they were immediately and snapped them up for a reasonable price.  It sure beats trying to re-wind a set of coils yourself.  The coil socket is safe due to the capacitors coupling the tank circuit to the vacuum tube terminals, so there is no high voltage DC present to the external connections.


The DC filter capacitors were replaced summarily, and a few of the carbon resistors were replaced as well as they had drifted away from their nominal values.  The original dial scale was in decent shape, despite the actual dial being cracked from over-tightening the set screw.  It wasn't cracked in half at least.  The problem was the that indicated frequency wasn't really that accurate.  There was opportunity to make it better.

I removed the scale, and scanned it in.  This could then be imported into Inkscape and used as a template to make a new scale.  Drawing with Inkscape is a breeze once you get the hang of it.  The beauty is that it is all vector drawing, so any line can be re-adjusted with ease.  Aspects of the drawing can be separated by layers and even locked or hidden from view.  The first step was to create a relative scale, so I put a ring of the alphabet around the dial.  This relative scale was used to create a chart of data for making a calibrated dial scale as compared to a frequency counter. 


The lower frequencies could be inductively coupled to the frequency counter using a similar coil.  The higher frequencies would not couple this way and had to be capacitively coupled into a short coax "antenna" into the frequency counter.  Once the table of data was filled in for each coil, then I could finished drawing all the other band scales on the new dial label.  Yes, it was tedious, but it was worth it.  To get markers on the scales, I added intermediate nodes after the circles were converted to vector paths.  This made it easy to sub-divide points between places where I wanted a numeric label.  The text was written out in a straight line and then applied to the path.  This is a very clever method that I have employed before to get things to look just right.  I was able to eliminate the interior relative band scale, and put scales for the two additional low band coils.  I made sure 455khz was clearly marked.

  
By using the original scan as an image to trace over top, the size and shape was easily determined.  The scanned image opacity was reduced to show a ghost image of what I was starting with.  You can see the calibration of some of the coils was quite poor, while others were not too far off.


The Cly Institute would like to thank KA3LJL for the donation of this grid dip meter.  It will be a good addition to our array of vintage test equipment.

Friday, January 25, 2019

Automatic Radio Mfg. Co. model CL-100

When dealing with transformer-less AM radios a careless touch could be a shocking experience.  We've all been warned of the dangers and are not surprised.  However, this situation was shocking in another way.  When I opened this Automatic Radio Mfg. Co. model CL-100 made in Boston, MA, I discovered that it contained a printed circuit board.  According to the information on radiomuseum.org, I was expecting point-to-point wiring.  It must be a slightly newer model.  I didn't think that printed circuit boards became commonplace till the 60's.  I had not encountered an All American Five tube design that incorporated a printed circuit board.  According to radiomuseum.org Automatic Radio Mfg. Co. went out of business in 1957.  This doesn't sound correct, because I have seen documents of court cases between Ford Mo. Co. and Automatic into the late 1960's.

The backstory on this little clock radio is that it was one that I kept next to by bedside when I was a teenager.  I don't think I ever opened it up, I just ran it the way it was with the little bit of hum that it produced.  The alarm clock feature provided a soft wake-up as the tubes came alive in the morning when the alarm cam closed its contacts at the appointed hour.  The sleep feature provided a way to fall to sleep with music or news and have the radio turn off on its own.  It is a pretty clever little device.  It came out of the bottom of a box in the basement looking like this.  There is a white substance on the knobs, which appeared to be mold?!?!  (I have noticed this on the old Magnavox TV that is still in that basement.)

The case opens easily by popping the cardboard back off.  That will need some tender loving restoration as it has begun to split.  The tag is still legible, but doesn't really contain a year of manufacture.  The quality control stamps are still visible.  I only gently cleaned the chassis because it has a nice protective layer of waxy cosmoline on it.  This protective layer has preserved the chassis and all the components from any oxidation.  I've seen this on a few circuit boards in the past, but not as generous an application on a tabletop radio like this.


The knobs pop off and the four screws in the bottom allow the chassis to slide out.  The only trick was gently prying off the clear front pieces so that the tuning pointer could be removed.  The once bright and shiny gold bezels are faded.  I think that some gold leaf paper from the craft store would look grand when properly cut and pasted in.  There's no preserving what is there.  It looks awful.

The plastic case itself is unbroken, but scratched and marked.  Some gentle rubbing with a Mr. Clean magic eraser pad cleared off the marks.  Some additional polishing to buff out the case may be needed as final preparation for re-assembly.  Overall it looks good for its age, and only one knob is missing.

The cosmoline impregnated a lot of dust on the top of the board over the years and I decided to leave it alone.  It ran when parked, remember.  All it should need is a few capacitors and maybe an alignment tweak.  The capacitors were all common values and quickly replaced.  The circuit board itself is strong, but the traces are pretty fragile.  Much care was given to keep from destroying the integrity.  The main filter cap was easily pulled out with only minor damage to the surrounding traces.  A dremel tool easily sliced through the electrolytic body after removing the cardboard cover.  Once free the base of the original capacitor is re-usable as a carrier for the new filter capacitors.  They are too big to fit in cross-ways, but fit nicely stacked one on top of the other with some lead extensions.  The mounting leads had to be drilled through to make contact with the actual contacts since the interior of the rivets and feed wires out of the original capacitor guts are aluminum.  The cardboard cover was re-used to hide the capacitor modification.

What is this big mystery component in the middle of the board?  It is large and square.  Is it a resistor / capacitor network?  I didn't pay much attention as long as the radio decides to play.

Which it did after all the paper capacitors and burst bumble-bee cap was replaced.  And it plays beautifully with no hum and good station selectivity.  To make it safe a new cord is in order.

Directing our attention back to the case, the bezels needed attention to make this piece of atomic age art presentable.  I visited the local craft store and found some nice bronze-colored plastic film.  It is quite thick and actually challenging to cut with a razor blade.  I think it will work just fine hidden behind the plastic bezels.

For a final product, I would say that it turned out really well.  It looks the part, it plays, and it keeps time.  What more could I want !



Wednesday, January 9, 2019

Silicone Grease

Silicone is a wondrous material.  It has so many uses and comes in quite a few forms. 

Let us consider Silicone Grease.  It exhibits excellent dielectric properties.  It can be used inside UHF connectors before they are wrapped for outdoor waterproofing. It can be used on spark plug wire boots to facilitate easy removal. Silicone grease is safe for plastic and paint.  It can be applied as a lubricant to plastic, such as drawer runners. Lubricating refrigerator drawers is my XYL's favorite usage. 

I have used it to lubricate sticky mic PTT buttons.  (No one wants to be THAT guy who gets his mic stuck on keying the repeater for hours.)

de N3FIX

Tuesday, December 18, 2018

Packet Radio - BBS generate Automatic Bulletin

Packet radio is fun and all but if you want to be serious about generating useful bulletins it is rather a chore to type them up.  What is required is a way to post an automatically generated bulletin from a text file source.  Sounds easy right?  It actually is.  This is designed around a Linux operating system, and some pre-requisite software is required.
BPQ32, expect, and telnet
Install these packages on your Linux computer like you normally would.  In this example I will show how to use any text file that you might generate, and post it as a BBS Bulletin.

Let's start with a text file.  It can be any text file, the internet of things and a home automation system allow us to capture data around us and put it in a text file reporting values for a day.

The Telnet access to BPQ32 (or linbpq) in this case must be set up correctly.  This will give us command line access to the packet BBS, and therefore the world if we want.  The expect command in Linux is clever.  It expects some output from stdout and replies with a response on stdin.  It will just be like typing the information into the command line yourself, only the .exp script will do it for you.  The text file is read in and translated into binary, this is key otherwise the file will not maintain the formatting it originally had.  No one likes long lines on a BBS system.  Keep it to less than 80 characters across when you generate your text file.  Then the expect command can spawn a telnet connection and step through logging into your BBS to send a bulletin.  You might want to just verify your login prompts on your own BBS.  They may differ, change any text in quotes after the expect command to match your system.  Finally the bulletin text can be inserted and the expect script can just log itself out of the telnet connection.

You will notice a \r at the end of some of the commands.  This is a carriage return, just like hitting enter on the keyboard.  Without it the command won't hit enter and won't go to the next step, so don't forget them.

In your home directory (in this case I'm running this on a Raspberry Pi), so the /home/pi directory I've made a folder called BBSScript.  My telnet host actually runs on a non-standard port 8010, so you'll have to change that and any other text in bold to suit your needs.  My standard outgoing message file is msgout.txt, and in the example it is being sent to SUBJECT@WW.  You can categorize your bulletin however you like.  Save the file as sendbulletin.exp and make it executable with a chmod u+x command.
#!/usr/bin/expect
set timeout 20
set msgfile [open "/home/pi/BBSScript/msgout.txt" r]
fconfigure $msgfile -translation binary
set msgout [read $msgfile]
close $msgfile
spawn telnet localhost 8010
expect "user:" { send "MYCALLSIGN\r" }
expect "password:" { send "MYPASSWORD\r" }
expect "MYALIAS:MYCALLSIGN} Nodes" { send "bbs\r" }
expect "BBS>" { send "sb SUBJECT@WW\r" }
expect "Enter Title (only):" { send "BULLETIN SUBJECT\r" }
expect "Enter Message Text (end with /ex or ctrl/z)" { send "$msgout\r" }
expect "EOF" { send "/ex\r" }
expect "BBS (Expert)>" { send "b\r" }
That's the extent of it.  It is really that easy.  Have another shell script overwrite your msgout.txt file daily, weekly, or any time via a crontab job.  Then call this exp script for automatic bulletin generation.  You can even call this script from inside your other script.

The last post I made about the weather report on AllStarLink can be modified to gather your weather from the internet and generate the msgout.txt file.  Think up your own clever bulletin topic.



73 and good DX
de N3FIX

Sunday, December 16, 2018

HamVOIP AllStarLink node weather script

I wrote this script early in the year, and it works rather well.
The script uses the national weather service to get a text transcription of the weather forecast.
It re-formats the text taking out the header and footer.
It then uses a text to speech translator to create a .ul file which can be read over the air by Asterisk.
(the Linux computer must have tts_audio installed)
Another crontab deletes the .ul file at midnight.

This is implemented on a hamvoip node on a Raspberry Pi.
It can be triggered by DTMF tones or on a time schedule.

The script is written below

73

N3FIX

----------------------------------------------
# script written by N3FIX
# date 2018-JAN-13
# this script downloads the weather forecast
# strips the header and footer
# converts it from a txt file to a .ul file
# and plays the .ul file on the air.
# play the forecast at 8:00 am and edit the crontab
# crontab -e
# 00 8 * * * /etc/asterisk/local/Forecast.sh

# use the lynx dump command to get the current weather forecast
# determine zone from alerts.weather.gov
# zone is PAZ065
lynx --dump "http://forecast.weather.gov/MapClick.php?zoneid=PAZ065&FcstType=text&TextType=2" > Forecast.txt

# take the header out by removing lines 2 through 4.
sed '2,4d' /etc/asterisk/local/Forecast.txt > /etc/asterisk/local/Forecast1.txt

# take the footer out by listing the file backwards with tac and taking out lines 1 to 10.
tac /etc/asterisk/local/Forecast1.txt | sed '1,10d' | tac > /etc/asterisk/local/Forecast.txt

# remove all the underscores from the file
sed 's/_//g' /etc/asterisk/local/Forecast.txt > /etc/asterisk/local/Forecast1.txt

# tts_audio doesn't say winds correctly. Make her say "wend" instead.
sed 's/winds/wend/g' /etc/asterisk/local/Forecast1.txt > /etc/asterisk/local/Forecast.txt

# convert the file to a ul file using tts_audio.sh
tts_audio.sh /etc/asterisk/local/Forecast.txt

# play the resulting file on the air by calling asterisk
# for 46891 ... insert your own node number
asterisk -rx "rpt localplay 46891 /etc/asterisk/local/Forecast"

# remove the temporary files after debugging
rm /etc/asterisk/local/Forecast1.txt
rm /etc/asterisk/local/Forecast.txt
------------------------------------------------