Tuesday, October 23, 2018

IC-28A Volume and Squelch

My first 2m mobile rig was the IC-28A.  With a healthy 25w output on high and a 5w output on low, it is compact and a good little radio.  I gave $20 at a hamfest and I still use it as my go-kit radio for events and the XYL's car.

The volume and squelch controls were getting pretty scratchy.  The volume finally gave up and wouldn't make contact with the wiper, which meant full volume!

Consulting the manual showed that Mouser had the parts in stock

Mouser #:688-RK097111202P
Mfr. #:RK097111202P
Desc.:Potentiometers Potentiometers Flat 25mm 10k


Mouser #:688-RK0971114D0B
Mfr. #:RK0971114D0B
Desc.:Potentiometers Potentiometers Flat 15mm 10k

What was not apparent at first was that the pin arrangement spacing on the volume control was not exactly the same.  This required some modification to the sub board.  A #61 drill bit in a manual push drill made short work of this small modification.  The potentiometer tabs were easily bent over to make contact with the original pads.


The other difference that had to be dealt with was the difference in the shafts.  The original was a splined shaft, these new pots have a D shaft.  Adapting the original knobs was reasonably easy.  Since they are plastic and have a bit of elasticity, they were drilled out with an interference fit.  They could then be pressed on the D shaft and still stay in place.

The next project for this radio will be to build a Lithium battery pack for it and make it so it can be mounted to my bicycle.

Thursday, September 20, 2018

Icom HM-151 microphone data mute mod

I found the design of the Icom HM-151 lacking in that it did not mute the microphone when running data modes through my SignaLink.  The solution is simple.  Install a tiny relay so that the microphone element is only connected to the radio when the PTT button on the handheld mic is pressed.

The tiny relay I found was actually Double Pole Double Throw.
NEC Miniature Non Latching DPDT Relay 5V 1A SMD SMT EB2-5NF


The specifications were quite impressive and the relay coil draw is very low, which is ideal for powering from the little Q1 pass transistor in the mic.

It was easily tacked into the circuit.  First the mic trace on the board had to be cut off.  I did this with an engraving tool.  See the X on the board where the trace was ground away.

The Common (Pin 8) and Normally Open (Pin 7) relay contacts were soldered directly to the board to reduce lead length.  The un-used pins were bent carefully out of the way.

The coil minus lead (Pin 1) was soldered to the PTT button contact.
The coil plus lead (Pin 10) was soldered to J2 pin 2, which is +5 volts.



The results are good.  I can run the local Data Net without fear of background noise, and I don't have to unplug my mic cable.

Saturday, August 4, 2018

TS-440s VCO potting

This Kenwood TS-440s was reported to have PLL issues.  After doing some research it was discovered that the potting material in the VCO was prone to turn conductive after many years.  This throws off the VCO especially in humid environments.

The repair is relatively easy, but labor intensive.  The top cover is removed and the first board flips up out of the way.  The board underneath only has a few connectors and comes out of the case rather easily.


The can around the VCO is best removed to perform this repair.  A few quick turns with the desoldering tool and the can can be separated from the board.  The potting material adheres to the can, but a dental pick can be used to pull and pry and material away gently.  The adjustable transformer also had to be removed to get the potting material out from underneath it.



They say there is better life through chemistry and the proof is here.  The potting material residue on the can was the perfect test subject for what chemical would be best to dissolve it rather than trying to pick it out a little at a time.  It turns out that ordinary brake cleaner softened the potting material back to a jelly-like state, but did not hurt the components on the board.  Dark places around certain components lead me to believe that this was the more overheated and more conductive material.  It was harder to remove and took more scraping with the dental pick.

When all the potting material was removed, the can could be soldered back in, and the radio re-assembled.


A quick test with the SDR proved that the transceiver did not drift when connected to a dummy load.  An on-air QSO confirmed that the audio was good on TX, and listening to WWV confirmed that the alignment was good for RX.


Saturday, July 21, 2018

CT-30 CTCSS tone board build

This is a brief review and test of the CT-30 Tone PL Tone board by Repeater Builder.  W3KKC designed this board basically from the application note from the FX-465 tone chip.  The board comes in assembled and kit form with everything you need.  I opted to build it from a kit.  The W3HZU 53.97Mhz repeater will be using this board in conjunction with the new HAMVOIP AllStarLink controller that we'll be installing soon.

The build is straightforward and well documented.  Even the greenest aspiring repeater owner can put this together and start using it.

Here's the initial test of the board proving it operates correctly.


Here's a walk through of using the board for Tone Decoder operation.

Friday, July 6, 2018

Software Defined Radio - Another Use

Sometimes you have to make do with what you have.  That means using tools that we have on hand differently than they way they were intended.

For instance this weekend I had to do an alignment procedure on customer's older rig that had a master oscillator and secondary oscillator that were out of calibration.  The frequency counter in the workshop just didn't have the amplification required to pick up the low amplitude signals associated with those circuits.

It occurred to me that an SDR (Software Defined Receiver) has tremendous accuracy and ability to concentrate on a small bandwidth.  This seemed ideal.  So I hauled the laptop down to the workshop and connected a spare 'scope probe to the test point in the radio that needed the alignment.  I didn't even have to connect the antenna terminal to the scope probe.  I just wound the lead around a rubber-duck antenna on the SDR.  The signal coupling was good enough to pick up a distinct hump on the spectrum.

It was easy to zoom into the signal and see when the oscillator was right on target for calibration.  A little tweak on the calibration adjustment in the customer's rig and everything was back in tolerance.

There's no excuse for anyone to be without an SDR these days considering the price.  The next step will be to get more familiar with GNU RADIO.  Tools like this would allow a user to create more useful applications than just the standard SDR tuner.  Why not a service monitor?  Why not a deviation meter?

We will get one of our software developers on that right away....

73 and happy hacking...

Tuesday, July 3, 2018

Antenna Switch repair

Here we have a rather nasty coaxial antenna switch.  It seems to operate alright when the contacts actually make contact.  This switch gave us trouble on Field Day, and I'd like to keep it in the arsenal. 
This is something we can fix.

Taking the back off the switch the internals are clearly visible.  The nuts are soldered on, so a little de-soldering is needed to get them apart.


The concept is to re-enforce the contacts with some helper-springs behind it.  I made the helper springs out of some stainless steel.  It has a good spring quality to it and will help hold the contacts down.


The whole thing was then re-assembled with the springs pushing down on the contacts.  The nuts were tightened back up and some solder re-applied to keep them from loosening.

Monday, April 16, 2018

Dual Rectifier Adapter

What happens when there is no more stock of 6H6 dual rectifier tubes, but plenty of 6AL5 tubes?  This situation clearly calls for an adapter.

Take a base from a dead tube and remove the tube by breaking it and de-soldering the leads.
Take a tube socket from an old TV chassis and wire the leads to match.

The result is a convenient adapter that can be applied to a classic radio without making any modifications to the vintage equipment.


6H6       6AL5
  2              4
  7              3
  5              7
  3              2
  8              1
  4              5